CNC, MILLING MACHINE G CODE, M CODE, VMC MACHINE, G CODE EBOOK, M CODE EBOOK
Topic:
1. Introduction
2. What is CNC?
3. Composition of a Part Program
4. Main Program Structure
5. Sub Program Structure
6. Sub Program Commands - General Notes
7. Sub Program Repeat Command
8. Billet Definition
9. Program Numbering and Saving
10. Program Block Numbering
11. Block Configuration
12. G Codes (Preparatory Functions)
13. Tool Movement
14. Feed Function
15. M Codes (Miscellaneous Functions)
16. Spindle Speed Function (Cutting Speed)
17. Tool Function
18. Tool Compensation (Tool Offset)
19. Absolute and Incremental Co-ordinates
20. Optional Block Skip
21. Tutorials and Comments
22. G Codes - Introduction
23. List of G Codes supported by
24. GØØ (Rapid Positioning/Traverse)
25. GØ1 (Linear Interpolation)
26. GØ2 & GØ3 (Circular Interpolation)
27. GØ4 (Dwell)
28. G2Ø & G21 (Imperial /Metric Data Input)
29. G28 (Reference Point Return)
30. G4Ø, G41 & G42 (Cutter Compensation)
31. G73-G89 (Canned Cycles)
32. G73 (High SpeedPeck Drilling)
33. G74 (Counter Tapping)
34. G76 (Fine Boring)
35. G8Ø (Canned Cycle, Cancel)
36. G81 (Drilling - Spot Boring)
37. G82 (Drilling - Counter Boring)
38. G83 (Deep Hole Peck Drilling)
39. G84 (Tapping)
40. G85 (Boring)
41. G86 (Boring)
42. G87 (Back Boring)
43. G89 (Boring)
44. G Codes - Program Example Using Canned Cycles
45. G9Ø (Absolute Zero Command)
46. G91 (Incremental Command)
47. G94 (Feed per Minute)
48. G95 (Feed per Revolution)
49. G98 (Return to Initial Level)
50. G99 (Return to R Point Level)
51. G17Ø-G173 (Circular/Rectangular Pocket)
52. G17Ø & G171 (Circular Pocket Example A)
53. G17Ø & G171 (Circular Pocket Example B)
54. G17Ø & G171 (Circular Pocket Example C)
55. G172 & G173 (Rectangular Pocket Example A)
56. G172 & G173 (Rectangular Pocket Example B)
57. G172 & G173 (Rectangular Pocket Example C)
58. M Codes - Introduction
59. List of M Codes Supported by
60. MØØ (Program Stop)
61. MØ1 (Optional Stop)
62. MØ2 (Program Reset)
63. MØ3 (Spindle Forward)
64. MØ4 (Spindle Reverse)
65. MØ5 (Spindle Stop)
66. MØ6 (Automatic Tool Change)
67. MØ8 (Coolant On)
68. MØ9 (Coolant Off)
69. M1Ø (Vice Open)
70. M11 (Vice Close)
71. M13 (Spindle Forward and Coolant On)
72. M14 (Spindle Reverse and Coolant On)
73. M2Ø (ATC Arm In)
74. M19 (Spindle Orientation)
75. M21 (ATC Arm Out)
76. M22 (ATC Arm Down)
77. M23 (ATC Arm Up)
78. M24 (ATC Drawbar Unclamp)
79. M27 (Reset Carousel to Pocket One)
80. M25 (ATC Drawbar Clamp)
81. M3Ø (Program Reset and Rewind)
82. M32 (Carousel CW)
83. M33 (Carousel CCW)
84. M38 (Door Open)
85. M39 (Door Close)
86. M62, M63, M64, M65, M66, M67
87. M7Ø (Mirror in X On)
88. M71 (Mirror in Y On)
89. M8Ø (Mirror in X Off)
90. M81 (Mirror in Y Off)
91. M98 (Sub Program Call)
92. M99 (Sub Program End and Return)